Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Whirlpool specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 589-6107 Book a Service Call
Error code · Washer

Whirlpool Washer Code F0E4: Water Hotter Than Expected at the Fill

F0E4 tells you the washer senses water that is too hot. On the Whirlpool all-in-one washer-dryer WFC8090GX it is an over-temperature on the wash cycle, and the unit must be connected to the cold water supply…

Medium · inspection needed
Book a Service Call(713) 589-6107
Code
F0E4
Appliance
Washer
Brand
Whirlpool
Warranty
30-day workmanship

What F0E4 means

F0E4 tells you the washer senses water that is too hot. On the Whirlpool all-in-one washer-dryer WFC8090GX it is an over-temperature on the wash cycle, and the unit must be connected to the cold water supply only. On stacked laundry towers, front-load Duet and WFW washers such as the WFW5620HW, and top-load HE washers such as the WTW5000DW, the direction is to check that the hot and cold hoses are not swapped. The cycle stops and F0E4 shows.

Common causes of F0E4

  • Hot and cold fill hoses connected to the wrong valves
  • A washer-dryer attached to a hot supply
  • A control that stopped and needs a power reset
  • Water temperature sensing, which we test if the hoses are correct
✓ One safe check you can try

1. Look at the two hoses behind the washer and confirm hot and cold are on the correct inlets. 2. On the washer-dryer, confirm the unit is connected to cold water only. 3. Reset by unplugging: 30 seconds on a laundry tower, 5 minutes on a front-load or top-load washer. 4. Plug in, start a cycle, and stop and call if F0E4 returns.

! Why to stop there
  • If the hoses are right and the code returns, the temperature sensing or the inlet valves need testing.
  • We check what temperature the fill really arrives at.
  • You hear the price in writing before work, and we say plainly if an older machine is not worth the repair.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

Lid Lock FlashingWhirlpool Top-Load Washer Lid Lock Light Flashing: Lock Fails to Engage Water Tap is ClosedWhirlpool Washer Symbol "Water Tap Is Closed": Water Is Not Arriving Lo FLWhirlpool Front-Load Washer Code Lo FL: Not Detecting Enough Incoming Water What does the "SUD" or "SD" meanWhirlpool Washer Display SUD or SD: What It Means and How to Clear It LoCWhirlpool Front-Load Washer LoC or LC: Control Lock Is Switched On Multiple Lights FlashingWhirlpool Top-Load Washer with Several Lights Flashing: Out-of-Balance Load No Water DetectedWhirlpool Front-Load Washer Message "No Water Detected": What to Check OFb or ofbWhirlpool Top-Load Washer Code OFb or Ofb: Load Out of Balance
F0E4F0E4 questions
Why would a washer think the water is too hot?

Often the hoses were swapped at installation, or after a move. It can also be a washer-dryer connected to a hot line when it needs cold only.

Can I swap the hoses myself?

Turn off the faucets, then switch the hoses back to their correct inlets and check for drips. If the connections are stiff or corroded, we can do it.

What if F0E4 shows after a correct reset?

Then we measure the temperature of the incoming water and test the sensing and the valves. We explain what we find in plain words and quote the work in writing first.

Book a visit

Still seeing F0E4?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 589-6107