Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Whirlpool specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 589-6107 Book a Service Call
Error code · Washer

Whirlpool Front-Load Washer Code F3 E6: Try One Reset Before Booking a Visit

If your Whirlpool front-load washer from the Duet and WFW line, such as the WFW90HEFW or WFW5620HW, stops on F3 E6, the instructions are plain and short: cycle power to the control by unplugging for 5…

Medium · inspection needed
Book a Service Call(713) 589-6107
Code
F3 E6
Appliance
Washer
Brand
Whirlpool
Warranty
30-day workmanship

What F3 E6 means

If your Whirlpool front-load washer from the Duet and WFW line, such as the WFW90HEFW or WFW5620HW, stops on F3 E6, the instructions are plain and short: cycle power to the control by unplugging for 5 minutes. Nothing in them names a sensor, a pump or any other part. The code applies to current and older generations alike. F3 E6 is therefore a control-level stop, and we read it that way until testing says otherwise.

Common causes of F3 E6

  • A control that locked up and recovers after a reset
  • A control or wiring condition that returns
  • A loose plug or a failing outlet
✓ One safe check you can try

1. Unplug the washer from the wall. 2. Give it a full 5 minutes with no power and no button presses. 3. Plug in, close the door, and run a short cycle. 4. If F3 E6 returns, book service rather than resetting again, and note when in the cycle it appeared.

! Why to stop there
  • One reset shows whether this was a one-off, and nothing more.
  • If F3 E6 repeats, the control and its connections need testing.
  • The price is in writing before work, and we say plainly if an older washer is not worth it.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

oLWhirlpool Top-Load Washer Code oL: Overloaded Tub PFWhirlpool Washer Code PF: Power Failure During the Cycle Rinse Light OnWhirlpool Top-Load Washer Rinse Light On: Spray Rinse in Progress rLWhirlpool Front-Load Washer Code rL: Items Found During Clean Washer LdWhirlpool Top-Load Washer Code Ld: Water Is Slow to Leave the Tub Sd or 5dWhirlpool Top-Load Washer Code Sd or 5d: Suds Reduction Is Running LdLWhirlpool Top-Load Washer Code LdL: Lid Fails to Lock Sense and Wash FlashingWhirlpool Top-Load Washer Sense and Wash Lights Flashing: Unbalanced Spin
F3 E6F3 E6 questions
Should I reset it more than once?

One careful 5-minute reset is a fair test. If F3 E6 comes straight back, more resets only waste time and we should look at the control.

Will F3 E6 damage my clothes?

No, but wet laundry should not sit for days. Once the washer is working, run a rinse and spin, or hang the clothes to dry.

What happens at the visit?

We read the washer, test the control and its connections, explain what we find in plain words, and give you a written price before any work starts.

Book a visit

Still seeing F3 E6?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 589-6107