Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Whirlpool specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 589-6107 Book a Service Call
Error code · Washer

Whirlpool Laundry Center Washer Code E2: Drain Alarm After 8 Minutes

Here E2 is a draining alarm on the washer section of an older Whirlpool stacked laundry center, one of the models that print error codes. The control sees water still draining after 8 minutes and stops…

Medium · inspection needed
Book a Service Call(713) 589-6107
Code
E2
Appliance
Washer
Brand
Whirlpool
Warranty
30-day workmanship

What E2 means

Here E2 is a draining alarm on the washer section of an older Whirlpool stacked laundry center, one of the models that print error codes. The control sees water still draining after 8 minutes and stops the cycle. You find standing water in the tub, a washer that will not spin, and E2 on the display. This model is old but still common. We work on it, and if a repair would not pay off we say so openly.

Common causes of E2

  • A clog or kink in the drain hose
  • A drain hose raised higher than the 100 cm limit from the floor
  • A drain pump that is slow or partly blocked
  • A drain standpipe or house drain that is backing up
✓ One safe check you can try

1. Unplug the unit and keep towels ready for leftover water. 2. Check that the drain hose is not more than 39 1/3 inches (100 cm) above the floor. 3. Straighten any kink and remove clogs you can see from the hose. 4. Make sure the wall standpipe is clear, then plug in and restart the cycle.

! Why to stop there
  • If the hose and standpipe are clear, the pump or its passage needs inspection.
  • We check whether the slow drain is the washer or the house line.
  • You get a written price before work and a 30-day workmanship warranty.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

oLWhirlpool Top-Load Washer Code oL: Overloaded Tub PFWhirlpool Washer Code PF: Power Failure During the Cycle Rinse Light OnWhirlpool Top-Load Washer Rinse Light On: Spray Rinse in Progress rLWhirlpool Front-Load Washer Code rL: Items Found During Clean Washer LdWhirlpool Top-Load Washer Code Ld: Water Is Slow to Leave the Tub Sd or 5dWhirlpool Top-Load Washer Code Sd or 5d: Suds Reduction Is Running LdLWhirlpool Top-Load Washer Code LdL: Lid Fails to Lock Sense and Wash FlashingWhirlpool Top-Load Washer Sense and Wash Lights Flashing: Unbalanced Spin
E2E2 questions
What triggers E2 on this washer?

The washer is still pumping water out after 8 minutes, so it gives up and stops the cycle. A kinked or blocked hose, or a hose set too high, is the first thing we look at.

Will water spill when I check the hose?

Some may. Unplug the unit and put towels and a shallow pan under the hose connection before you pull it free, and keep the free end low so the water in the hose runs into the pan rather than the floor.

Should I replace this old laundry center?

Not necessarily. Drain repairs are usually moderate in cost, and a clogged hose costs far less than a new unit. We quote first and tell you plainly if the machine's age says to save your money.

Book a visit

Still seeing E2?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 589-6107