Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Whirlpool specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 589-6107 Book a Service Call
Error code · Dryer

Whirlpool Dryer Code F3 E4: Five-Minute Breaker Reset

F3 E4 shows on WED / WGD electric and gas Whirlpool dryers, Cabrio and Duet generations included. The maker names no part for this code and gives only a longer power reset, so we treat it…

Medium · inspection needed
Book a Service Call(713) 589-6107
Code
F3 E4
Appliance
Dryer
Brand
Whirlpool
Warranty
30-day workmanship

What F3 E4 means

F3 E4 shows on WED / WGD electric and gas Whirlpool dryers, Cabrio and Duet generations included. The maker names no part for this code and gives only a longer power reset, so we treat it as a temperature-sensing or control code that the dryer's electronics could not settle. You may see the code with the cycle stopped or heat missing. Unlike many dryer codes, the listed reset here is a full five minutes at the breaker, not one.

Common causes of F3 E4

  • Temperature sensing circuit in the dryer
  • Control board response after power-up
  • Wiring and connectors in the heat path
  • Airflow through the lint screen and vent
✓ One safe check you can try

1. Switch off the dryer's circuit breaker for a full 5 minutes. 2. Switch the breaker back on. 3. Start a timed dry cycle. 4. Watch the dryer for a minute to confirm F3 E4 stays away. 5. If the code reappears, leave the dryer off and book a visit.

! Why to stop there
  • The maker does not tell us which part this code is tied to, so we find it by testing
  • We check sensors, wiring and the control in order rather than swapping parts
  • We quote the price in writing first, and we tell you if the dryer is too old to be worth repairing
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Dryer codes

tSWhirlpool Dryer Code tS: Thermistor Reading Out of Range Water TankWhirlpool Dryer Message Water Tank: Tank Full or Not Seated LocWhirlpool Dryer Code Loc: Control Lock Turned On by Mistake PFWhirlpool Dryer PF Code: Power Failure During a Cycle F6E2Whirlpool Tower Dryer Code F6E2: Control Link Check with Five-Minute Reset F6E3Whirlpool Dryer F6E3 Code: Control Alert on Three Models F6E4Whirlpool Laundry Tower Dryer F6E4 Code: Control Communication with the Panel F6E5Whirlpool Laundry Tower Dryer Code F6E5: Control Link Lost
F3 E4F3 E4 questions
Why is the reset five minutes for F3 E4?

That is the wait listed for this code, longer than the one-minute reset used for several others. It gives the control time to clear fully before you start a cycle again.

Does F3 E4 mean the heater is dead?

Not necessarily. The code does not name the heater or any other part. We test temperature sensing and the heat circuit before saying which part, if any, needs replacing.

What if the code only appears sometimes?

An intermittent code often means a connection or sensor that wanders in and out of range. Note when it appears, such as heavy loads or long cycles, and tell us. That helps us find it faster.

Book a visit

Still seeing F3 E4?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 589-6107