Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Whirlpool specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 589-6107 Book a Service Call
Error code · Washer

Whirlpool Washer Code F2E3: Control Unit, Interface or Wiring Needs a Look After a Reset

F2E3 is shown on two Whirlpool platforms. On the washer section of a laundry tower or stacked laundry center it lists a communication problem as the potential cause. On top-load HE washers, the Cabrio and WTW…

Medium · inspection needed
Book a Service Call(713) 589-6107
Code
F2E3
Appliance
Washer
Brand
Whirlpool
Warranty
30-day workmanship

What F2E3 means

F2E3 is shown on two Whirlpool platforms. On the washer section of a laundry tower or stacked laundry center it lists a communication problem as the potential cause. On top-load HE washers, the Cabrio and WTW family such as the WTW5000DW and WTW7500GC, an older platform still in many homes, it says there may be an issue with the control unit, the user interface or the wiring between them. Both call for a 5-minute power reset. These older washers can be repaired, and we are open with you when a repair is not worth doing.

Common causes of F2E3

  • A one-time communication stop that clears after a reset
  • A loose or damaged connection between the control unit and the interface
  • The control unit or the user interface itself, which we confirm by testing
✓ One safe check you can try

1. Unplug the washer and keep your hands off the control panel. 2. Leave it unplugged for a full 5 minutes. 3. Plug it back in, close the lid or door, and start a short cycle. 4. If F2E3 is still there afterward, stop using the washer and schedule service so the control can be tested.

! Why to stop there
  • The reset does not tell us whether the control unit, the interface or the wiring is behind F2E3.
  • We test each link on site, starting with the connections.
  • The price comes in writing before work, with a plain opinion on an older Cabrio.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

Rinse Light OnWhirlpool Top-Load Washer Rinse Light On: Spray Rinse in Progress rLWhirlpool Front-Load Washer Code rL: Items Found During Clean Washer LdWhirlpool Top-Load Washer Code Ld: Water Is Slow to Leave the Tub Sd or 5dWhirlpool Top-Load Washer Code Sd or 5d: Suds Reduction Is Running LdLWhirlpool Top-Load Washer Code LdL: Lid Fails to Lock Sense and Wash FlashingWhirlpool Top-Load Washer Sense and Wash Lights Flashing: Unbalanced Spin LdUWhirlpool Top-Load Washer Code LdU: Lid Is Unable to Unlock Spin Light FlashingWhirlpool Top-Load Washer Spin Light Blinking: The Basket Is Off Balance
F2E3F2E3 questions
What is the user interface on my washer?

It is the control panel with the display and buttons. F2E3 means the washer may not be reading it correctly, or may not be reaching the control behind it.

Is it a safety problem?

No. The washer stops rather than run on a bad signal. Do not open the panel yourself; a 5-minute unplug is the only owner step.

Is it worth repairing an older Cabrio?

Often it is, because control repairs vary widely. We quote in writing and say plainly if the age of the washer means it is better not to repair.

Book a visit

Still seeing F2E3?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 589-6107