Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Whirlpool specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 589-6107 Book a Service Call
Error code · Washer

Whirlpool Laundry Tower Washer Code F0E6: Measurement Sensor Flagged, Try a Power Cycle

On the washer section of a Whirlpool laundry tower or stacked laundry center, F0E6 points to the measurement sensor circuit. The display does not say whether that is the sensor, its wiring or the control reading…

Medium · inspection needed
Book a Service Call(713) 589-6107
Code
F0E6
Appliance
Washer
Brand
Whirlpool
Warranty
30-day workmanship

What F0E6 means

On the washer section of a Whirlpool laundry tower or stacked laundry center, F0E6 points to the measurement sensor circuit. The display does not say whether that is the sensor, its wiring or the control reading it, so we treat it as a circuit to test and not as a failed part. The washer stops and F0E6 stays on the display. The one owner step given for it is a power reset, which clears a one-time stop.

Common causes of F0E6

  • A one-time reading error that clears with a reset
  • The measurement sensor circuit or its connection
  • The control that interprets that signal
✓ One safe check you can try

1. Unplug the washer and leave it for 30 seconds. 2. Plug it back in, seating the plug firmly. 3. Close the lid or door and run a short cycle. 4. If F0E6 shows again, stop using the washer and schedule service.

! Why to stop there
  • A reset cannot tell us whether the sensor, wiring or control is behind F0E6.
  • We test the circuit on site and compare the reading to what the washer is doing.
  • You get a written price before we change anything.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

rLWhirlpool Front-Load Washer Code rL: Items Found During Clean Washer LdWhirlpool Top-Load Washer Code Ld: Water Is Slow to Leave the Tub Sd or 5dWhirlpool Top-Load Washer Code Sd or 5d: Suds Reduction Is Running LdLWhirlpool Top-Load Washer Code LdL: Lid Fails to Lock Sense and Wash FlashingWhirlpool Top-Load Washer Sense and Wash Lights Flashing: Unbalanced Spin LdUWhirlpool Top-Load Washer Code LdU: Lid Is Unable to Unlock Spin Light FlashingWhirlpool Top-Load Washer Spin Light Blinking: The Basket Is Off Balance LFWhirlpool Top-Load Washer Code LF: Tub Is Too Slow to Fill
F0E6F0E6 questions
What is the measurement sensor?

It is the circuit the washer uses to read a condition in the cycle. The code does not say which one, so we test the circuit instead of guessing.

Will unplugging the tower fix F0E6?

It may, if the stop was a one-time event. Wait 30 seconds, plug it in again and run a cycle. If the code comes back, it needs a visit.

Is it safe to use the dryer on top?

The dryer is its own section, but if the whole unit behaves oddly, stop using both. We will check the tower and explain what we find.

Book a visit

Still seeing F0E6?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 589-6107