Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Whirlpool specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 589-6107 Book a Service Call
Error code · Dishwasher

Older Whirlpool Built-in Dishwasher, Sanitize Light Flashing: Temperature Missed

Older Whirlpool built-in dishwashers, including the WDT750SAHZ, flash the Sanitize light when the cycle did not reach the sanitizing temperature. It is a plain indication that the dishes were not sanitized, not a sign the machine…

Low risk · DIY check OK
Book a Service Call(713) 589-6107
Code
Sanitize Light Flashing
Appliance
Dishwasher
Brand
Whirlpool
Warranty
30-day workmanship

What Sanitize Light Flashing means

Older Whirlpool built-in dishwashers, including the WDT750SAHZ, flash the Sanitize light when the cycle did not reach the sanitizing temperature. It is a plain indication that the dishes were not sanitized, not a sign the machine has stopped working. These older units are still in many homes, and we repair them. A common cause is household hot water that is not hot enough when the cycle begins, so check the tap first.

Common causes of Sanitize Light Flashing

  • Household hot water below the minimum when the cycle starts
  • Long pipe run delaying hot water to the dishwasher
  • Heater or temperature sensing in the dishwasher
  • Control reading cleared only by resetting
✓ One safe check you can try

1. Let the hot water run about 30 seconds at the closest faucet, and confirm it reaches at least 120 degrees F (49 degrees C), the minimum named in the owner's manual. 2. Reset the control by disconnecting power for one minute: unplug the dishwasher, or turn off its breaker if hard-wired. 3. Restore power and run a sanitize cycle. 4. If the light flashes again, call us.

! Why to stop there
  • Tap temperature is only part of the picture, because the dishwasher heats water itself too
  • An aging heater or sensor can fall just short of sanitizing temperature without any other sign
  • We tell you plainly when repair is not worth it on an older unit, and quote in writing first
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Dishwasher codes

Rinse Only LightWhirlpool Portable Dishwasher with the Rinse Only Light Flashing: Stuck Keys SaniLightWhirlpool Dishwasher Sanitize Light Blinking Because the Water Was Not Hot Enough Start/ResumeWhirlpool Portable Dishwasher Start/Resume Light Flashing: Cycle Interrupted F6E4Whirlpool Built-In Dishwasher F6E4: Float Switch and Leveling F7E2Whirlpool Dishwasher Code F7E2: Wash Motor Not Responding F8E1Whirlpool Dishwasher F8E1 or H20: Not Detecting Water F8E2Whirlpool Built-In Dishwasher F8E2 and the Fill Valve Circuit F8E4Whirlpool Dishwasher F8E4 Error on a New Install: Fill and Float Checks
Sanitize Light FlashingSanitize Light Flashing questions
Why does the Sanitize light flash after a cycle?

It flashes when the dishwasher detects that the sanitizing temperature was not reached. Dishes from that cycle were not sanitized, so rewash them once the water is hot.

How hot must the household water be?

At least 120 degrees F (49 degrees C), measured by running the hot tap about 30 seconds at the nearest faucet. Your water heater setting may be worth reviewing.

Is an older dishwasher worth fixing for this?

Often yes, since a temperature problem is frequently modest. We give an honest opinion and a written price, and we say so if replacement is the better choice.

Book a visit

Still unsure about Sanitize Light Flashing?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 589-6107